position
position

Why Choose a MATTON Autoclave Sterilizer? Retort Types, Suitable Foods, and a Buyer’s Checklist

Time:2026-10-27

An autoclave sterilizer and a retort machine are the same equipment: a sealed pressure vessel that heats packaged food above 121 °C so it stays safe without refrigeration. When selecting this type of equipment, there are three core questions you need to consider: Which type of sterilization retort is best suited for your specific packaging format? Can the equipment meet the processing requirements of your product? What equipment is needed for a complete production line, and what are the associated costs?
This guide will address each of these questions. Furthermore, we will explore the ideal use cases for MATTON sterilization retorts, providing detailed technical specifications, cost estimates, and real-world application examples.

Why choose a MATTON autoclave sterilizer?

Choose MATTON if you want a retort built for heavy daily cycling, with tight temperature and pressure control and lower maintenance cost than a plate-exchanger design. The main reasons:

  • Pressure vessel built to GB150-2011. The vessel is S30408 (06Cr19Ni10) stainless steel, with a maximum working pressure of 3.0 bar and a maximum temperature of 147 °C.
  • Tight control. Temperature is held to ±0.2 °C and pressure to ±0.01 MPa. A Siemens PLC stores hundreds of recipes behind tiered user permissions.
  • Two machine families. Top-spray (water spray) retorts and steam rotary retorts. MATTON client lines run cans, plastic bowls and bottles, glass bottles, and stand-up pouches.
  • Lower running cost. A spiral-wound tube heat exchanger needs 21 m² of surface where a plate exchanger needs 37 m² on the same retort, and it lets you use a smaller circulation pump.
  • Built for thermal cycling. The shell is rolled to a roundness deviation under 2 mm, the heads are pressed from a single plate, and the door flange is forged in two pieces. Heads and flanges are stress-relieved by vibration.

One caveat up front: no retort makes food safe on its own. The process itself (time, temperature, pressure, load pattern) has to be validated for your product. More on that below.

Are an autoclave sterilizer and a retort machine the same thing?

Yes. “Retort” is the term in U.S. food regulations, where 21 CFR Part 113 defines it as any closed vessel or other equipment used for the thermal processing of foods. “Autoclave” is the word more common in Europe, Asia, and laboratories. In a food factory, both names describe one job: commercial sterilization of sealed packages so they can sit on a shelf without refrigeration.

Types of autoclave sterilizers (retort machines)

Retorts differ in two ways: what carries the heat (steam, water, or a steam-air mix) and whether the load moves. This table shows how the common types compare.

Retort type Heating medium Typical packages What to know
Saturated steam, still Steam only Metal cans, other pressure-resistant packs Pressure follows steam temperature, so you can’t add overpressure. Poor fit for plastic bowls and pouches.
Water immersion Fully flooded vessel Pouches, trays, plastic bowls Air or steam supplies overpressure. Heating is even, but you heat a lot of water.
Water spray / cascade (top spray) Hot water recirculated and sprayed over the load Pouches, trays, bowls, bottles, cans Overpressure is set separately from temperature. Less water to heat than immersion.
Steam-air Steam and air mix, moved by a fan Flexible and semi-rigid packs Overpressure comes from the air ratio.
Rotary (agitating) Any of the above, with the basket turning Cans, jars, bowls, thick or particulate foods Motion moves heat through viscous products and can shorten cycles.

Overpressure decides which packages you can run. When a sealed package heats up, the pressure inside it rises. In a pure steam retort the outside pressure is tied to the steam temperature, so you can’t adjust it. Water-based and steam-air retorts let you add compressed air so the outside pressure can follow the inside pressure. USDA’s training material on overpressure retorts warns that too little overpressure can rupture containers, damage seals, slow heat penetration, or disturb water circulation in the vessel. That is why plastic bowls, PP bottles, and pouches usually go into water-spray, immersion, or steam-air retorts.

Top-spray (water spray) retorts

MATTON’s top-spray retorts recirculate hot water over the load. Because water is the heat carrier, temperature and pressure are controlled independently. You add compressed air or release pressure to balance what is happening inside the package. This suits packs that can’t handle a large pressure difference: PP bottles, plastic bowls, and packages that contain air. MATTON’s reference size in its documentation is DN1600 × 6300 mm.

Steam rotary retorts

In a steam rotary retort, the basket turns during the cycle. Thick foods like porridge barely move inside a still container, so the center heats slowly. Rotation mixes the contents and carries heat inward faster.

MATTON’s rotary retort handles canned porridge, pouch porridge, and condensed milk. It is also a multi-purpose vessel. For a plant with many product types, one rotary retort can replace several different retorts and save floor space.

Research supports agitation, with a catch. A Clemson University study on pouches found that how much motion helps depends on the product’s viscosity and the amount of residual air in the pouch. So test your own product and package before you commit.

Why choose a MATTON autoclave sterilizer? The details that matter

A pressure vessel built for daily cycling

The vessel is designed and made to GB150-2011, China’s pressure vessel standard. Everything that touches circulating water, including pipes and valves, is S30408 stainless steel, and the welding material matches. Insulation is 30 mm of aluminum silicate under a 0.6 mm stainless cover. During a cycle, the outside surface stays within 10 °C of room temperature.

If you install outside China, ask what pressure vessel documents your local rules require (ASME in the U.S. or the Pressure Equipment Directive in the EU, for example) and what MATTON can supply. Ask now, not at customs.

Instruments that match regulatory expectations

Under 21 CFR 113.40, a U.S. low-acid food retort needs an accurate temperature-indicating device, an accurate temperature-recording device, and an automatic controller. The indicating device, not the recorder chart, is the reference instrument.

MATTON retorts carry two Class A PT100 probes, a graduated mercury-in-glass thermometer, a pressure transmitter, a pressure gauge, an adjustable safety valve, and a liquid-level detector. The controller compares the two temperature readings all the time and warns the operator if one sensor drifts.

Safety interlocks are built in. A cycle can’t start unless the door is fully closed, and the door can’t open until pressure is released.

MATTON states that its equipment meets GMP and FDA requirements and that the design target is a contamination rate below one in a million. Read that carefully. It holds only when the process settings rest on the correct cold-spot position and temperature, and when products enter the retort in the same pre-sterilization condition. Those two things are on your side of the fence.

Recipe control that keeps the process from drifting

  • Permission levels. Administrator, process engineer, and operator roles. Only higher levels can edit a process. Operators run it.
  • Central recipes. A process created by QC downloads as a complete set to each retort. The same product can’t run with different settings on different retorts.
  • Hundreds of stored recipes, so each product and container gets its own process.
  • Full records. Temperature, pressure, time, valve positions, water level, and alarms are logged. An RS485 port is included.
  • Fully automatic cycle. Heat-up, sterilization, cooling, and drain run without manual steps. A manual control unit is there as a backup.
  • Siemens control system, so parts and support are easy to find worldwide. The interface is in Chinese and English.

Rotary parts built for maintenance

  • The rotating cage rides on a rear shaft and two idler rollers. A flat rear head lowers the bending load on the rear shaft and extends its life.
  • The idler roller bearings sit outside the seal ring, so they aren’t soaking in water. MATTON uses self-aligning roller bearings, which handle heavy loads at low speed. The front saddle side cover comes off for service.
  • MATTON states roughly one maintenance visit every 3 months on the idler rollers and a service life of 2 years or more.
  • The cage is balanced with counterweights, empty and loaded, which protects the gearbox.
  • The cage is built from welded tube sheets, so the clamping device can be repaired inside the retort without pulling the cage out.

Fabrication details you can ask any supplier about

These are worth asking every retort maker, not just us:

  • Shell: rolled on a CNC hydraulic plate-rolling machine (plate up to 50 mm, 400 mm rollers) with roundness deviation under 2 mm. Even rolling prevents stress concentrations that crack under repeated heating and cooling.
  • Heads: pressed in one piece from a single plate, then vibration stress-relieved.
  • Door flange: two forged pieces, CNC machined, then vibration stress-relieved.
  • Cutting and welding: laser cutting center and plasma welding center.
Retort Food Processing Audit Trail Records
Actual heat distribution test results from a MATTON retort

How much can a spiral-wound heat exchanger save?

The heat exchanger heats the circulating water and cools it again after sterilization. Many retorts use plate exchangers. MATTON uses a spiral-wound tube heat exchanger with heat exchange efficiency above 95%. The 10 mm tubes are 316L stainless steel. Tubes and shell are both stainless, so they expand together instead of straining each other.

Here is MATTON’s calculation for one DN1600 × 6300 top-spray retort, running 20 hours a day for 200 days a year:

Item Plate exchanger (BRH4C-37BH) Spiral-wound tube exchanger
Heat transfer area 37 m² 21 m²
Circulation pump 16 m head, 22 kW 10 m head, 15 kW
Gasket replacement (about 50 gaskets × 80 RMB, twice a year) 8,000 RMB a year None
Labor for gasket changes (3 workers × 2 days × 150 RMB, twice a year) 1,800 RMB a year None
Extra pump electricity (7 kW × 20 h × 200 days = 28,000 kWh at 1 RMB per kWh) 28,000 RMB a year None
Added yearly cost of the plate design 37,800 RMB None

That is roughly US$5,000 to US$5,500 per retort per year, depending on the exchange rate.

The maintenance side is just as real. According to MATTON’s calculation, plate gaskets last about 6 months at 0.5–0.6 MPa steam pressure. A plate exchanger weighs around 600 kg and sits 50–100 cm off the floor in a tight space where a forklift can’t reach. A full gasket change takes about 2 days with at least 3 people, followed by a pressure test. Late replacement risks steam leaks, burns, and under-processed product.

These are MATTON’s figures and assumptions. Your electricity price, shift pattern, and steam pressure will change the result, so plug in your own numbers before you decide.

What foods suit an autoclave sterilizer?

An autoclave sterilizer suits low-acid foods in sealed packages. FDA defines low-acid foods as those with a finished equilibrium pH above 4.6 and a water activity above 0.85 (UF/IFAS summary of the FDA definitions).

The pH 4.6 line comes from Clostridium botulinum. Its spores don’t grow below that pH, and the low-acid canned food rules (21 CFR Parts 108, 113, and 114) exist to keep them from surviving in sealed containers. See the UGA Extension explanation for the background.

Food group Examples Common packages Notes
Porridge, rice, grain dishes Eight-treasure porridge, rice Cans, plastic bowls, pouches Thick texture. A rotary retort helps heat move through.
Plant-based drinks and dairy Soy milk, coconut juice, pouch yogurt, condensed milk Glass bottles, PP/HDPE bottles, stand-up pouches, cans Overpressure control protects bottles and pouches.
Meat, poultry, blood products Duck blood, cooked meats Pouches, trays, cans Low-acid. Needs a validated process.
Vegetables, corn, beans Corn, beans, mixed vegetables Cans, pouches Cut size and fill level change heating time.
Soups, sauces, ready meals Soups, ready meals Pouches, bowls, trays Particles slow the cold spot.
Fish and seafood Canned fish Cans, pouches Low-acid. Needs a validated process.

The California Department of Public Health lists low-acid canned food examples such as vegetables, beans, rice, noodles, soups, fish, meat, and some dairy and non-dairy beverages.

What about acid foods? Foods with a natural pH of 4.6 or below, like most fruit, usually need only a milder heat treatment. A full retort may be more than you need. Foods that can’t survive pressure cooking without losing texture or color, like fresh leafy greens, are poor candidates too.

Which containers work? MATTON’s documents list plastic containers (high-temperature bowls, PP bottles, HDPE bottles) and metal containers (tinplate cans, aluminum cans). Client examples add glass bottles and stand-up pouches.

Who uses MATTON autoclave sterilizers?

autoclave sterilizer​
autoclave sterilizer​

Below are some project examples from MATTON’s client base:
• Piracanjuba: Rotary retorts for condensed milk.
• Agros Foods: Production line for ready-to-eat corn.
• Sanjianke Dairy Co., Ltd.: A production line for yogurt in stand-up pouches, utilizing 1500 × 6000 mm pressure retorts.
• Shandong Weizhen Food Co., Ltd.: A production line for soy milk in glass bottles, utilizing 1800 × 6500 mm pressure retorts.
• Yeniu: Production line for coconut milk.
As these examples demonstrate, the range of applications is extensive—covering meat by-products, vegetables, dairy products, plant-based protein drinks, and fruit juices—with packaging formats that include flexible pouches and glass bottles. This versatility is made possible by flexible pressure sterilization systems that feature precise overpressure control and process recipe management. You can learn more by exploring our client case studies.

How to choose a retort: step by step

  1. Classify your product. Measure finished pH and water activity. Above pH 4.6 and aw 0.85, you need a validated low-acid process.
  2. List every package. Material, shape, size, and how much pressure difference it tolerates. This narrows the retort type fast.
  3. Bring in a process authority. A qualified expert sets the scheduled process from heat penetration data. Some regions centralize this. California, for example, sends low-acid products to a University of California lab for evaluation.
  4. Pick the type and size. Use the table above, then size the vessel and basket count to your daily volume. The client examples above run 1500 × 6000 and 1800 × 6500 vessels.
  5. Check your utilities. Steam, compressed air, cooling water, and power. Overpressure retorts need a compressed air supply that can keep up.
  6. Audit the supplier. Ask for pressure vessel documents for your country, the instrument list, recipe and password controls, a spare parts plan, and a factory acceptance test.
  7. Validate on site. Run heat distribution and heat penetration tests with your real load before first production.

Common mistakes when buying a retort

  • Buying on price alone. The cheapest quote often hides a plate exchanger, a larger pump, and gasket changes every six months. Compare five-year running cost, not purchase price.
  • Skipping the heat distribution test. A retort can read 121 °C at the sensor and still have a cooler zone near the load. The test finds it.
  • Setting overpressure by guesswork. Too little can burst pouches and damage seals. Too much can deform bottles and lids. Test with your actual containers.
  • Ignoring maintenance access. A 600 kg exchanger in a cramped space is a two-day job for three people. Ask how each wear part gets changed.
  • Treating “FDA compliant” as a certificate. FDA’s rules cover your plant, equipment, and filed process together. A supplier’s statement is the start of your own review.
  • Forgetting local pressure vessel rules. GB150 is a Chinese standard. Confirm what your country requires before the machine ships.

FAQ

What is the difference between an autoclave sterilizer and a retort?

None in practice. Both are pressure vessels that heat sealed, packaged food to commercial sterility. “Retort” is the standard term in U.S. food regulation, and “autoclave” is more common in Europe, Asia, and labs.

Which retort is best for plastic bowls and PP bottles?

A water-based retort with independent pressure control, such as a top-spray retort. Pressure inside the container rises with temperature, so the outside pressure has to follow it. A top-spray retort lets you add or release pressure separately from temperature. Still, test the overpressure setting with your own containers.

What temperature does a food retort run at?

The validated process sets it, and it depends on product and package. Low-acid foods are often processed around 121 °C (250 °F). MATTON retorts are rated to 147 °C and 3.0 bar maximum working pressure, which gives room for different process designs.

Does FDA approve my retort?

Not as a product. For low-acid canned foods sold in the U.S., you register your plant and file each process with FDA, follow 21 CFR Part 113 including its equipment rules, and keep records. Meat and poultry products fall under USDA FSIS instead. See the FDA inspection guide for low-acid canned foods, and check the rules in your own country.

Get a retort sized for your line

Send us four things: your product and its pH, your package type and size, your daily output, and the utilities on site. We’ll come back with a recommended retort type and vessel size. Request a quote or browse the client case studies first.

 

Statement: This article was published after being reviewed by Mike 

mike

Mike

Global Solutions Director | Matton

12 Years. Mechanical Engineer. International Trade Expert. 4 years as a mechanical engineer in national research institutes and large factories, 6 years as an international trade manager, and 2 years of overseas work experience.

I help international clients navigate the complexities of China’s food and packaging machinery market. From factory planning to final machine inspection.

Specializations: Custom food machinery manufacturing, production line design, factory planning and construction, turnkey projects.
Retort machine overall solutions, frozen vegetable and fruit production lines, freeze-drying production lines, potato processing production lines, industrial dryers, frozen vegetable production lines, frying production lines, thermoforming packaging machines, pasteurization lines.

Get Expert Technical Advice | Free Product Quote